Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Oxnard Homeowners
A gate that won’t open, won’t close, or makes a grinding noise every time it moves isn’t something to put off. In Oxnard, coastal moisture and salt air work on hinges, tracks, and control boards year-round, and a gate that fails today usually failed in small ways for weeks first. We’re Gate Repair Oxnard, led by Lloyd Alvarado, and we repair the gate you already own and install the gate you’d rather have. From a Mighty Mule on a backyard fence in El Rio to a FAAC slide operator on a Channel Islands Beach driveway, we work on your brand. Call (833) 589-9922 for a free estimate, and we’ll get your gate moving again.
Most Oxnard repairs are completed the same day we arrive. We diagnose the exact failure, quote the price before any work starts, and stand behind the fix.
Driveway Gate Repair
Driveway Gate Repair means getting your automated or manual driveway gate opening, closing, and latching the way it should, whether it’s a swing gate on hinges or a slide gate on a track. You need it when the gate stops responding to the remote, the keypad, or the vehicle sensor, or when the motor runs but the gate barely moves. We open the operator, test the control board, check limit switches and safety edges, and either rebuild or replace what failed. For more detail, see The Complete Gate Repair Guide for Oxnard Homeowners; in Oxnard, most driveway gate repairs run between $185 and $650 depending on whether we’re replacing a sensor, a circuit board, or a motor assembly. We quote the number before any work begins.
Swing Gate Diagnosis
On swing gates, the first things we check are the hinge posts, the opener arm, and the travel limits. A gate that opens six inches and stops usually has a limit switch problem, not a dead motor. Lloyd and the team replace switches, re-align arms, and re-set travel so the gate stops exactly where it should.
Slide Gate Track and Drive
Slide gates fail most often at the track or the drive chain. We clear debris, inspect rollers, and re-tension chains so the gate doesn’t shudder or stall halfway. When the motor itself has burned out, we swap in a replacement rated for the weight and cycle count of your gate.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Welding
Gate Welding repairs the structural steel or aluminum frame of your gate when it cracks, sags, or separates at a joint. You need it when a hinge tears away from the post, when a bottom rail rusts through, or when an impact bends the frame out of square. We weld, grind, and reinforce so the gate is stronger at the repair point than it was originally. Gate welding in Oxnard typically runs $150 to $400 for a crack or hinge re-weld, and $400 to $900 when we’re cutting out and replacing rusted sections. The price is agreed before we strike an arc.
Hinge and Post Repairs
A gate that sags is usually pulling away from its hinge welds. We remove the gate, re-weld the hinges at the correct angle, and add gusset plates where repeated stress has fatigued the steel. The gate hangs square again, and the opener no longer fights the weight of a misaligned leaf.
Rust Section Replacement
Oxnard’s salt air gets into gate frames through pin holes and unsealed joints. We cut out the rusted section, weld in new steel matched to the original profile, and prime and paint the repair. You keep the gate you have instead of paying for a full replacement.
Commercial Gate Repair
Commercial Gate Repair covers the slide gates, barrier arms, and swing gates on apartment complexes, storage facilities, HOA entrances, and business properties across Oxnard. You need it when a gate holds up tenants, lets unauthorized vehicles through, or trips its breaker every afternoon. We service the professional-grade operators property managers actually have: LiftMaster, FAAC, BFT, and Linear, plus DoorKing on access-controlled entries. Commercial gate repair in Oxnard runs $250 to $1,200 depending on the operator type and whether we’re replacing a loop detector, a motor, or a full control board. We quote every job before we start.
Access Control and Loop Detectors
When the gate opens for outgoing traffic but not incoming, the loop detector under the asphalt has usually failed. We test the loop, replace the detector, and verify the gate holds on the safety loop before we leave. Lloyd Alvarado has worked on access systems from Oxnard industrial lots to gated communities near Casa Conejo, plus El Rio.
High-Cycle Operator Service
Apartment gates cycle hundreds of times a day. We rebuild or replace high-wear parts like limit switches, drive gears, and chain sprockets before they strand residents outside. When an operator is beyond repair, we install a new unit sized for the gate’s weight and daily traffic.
Iron Gate Repair
Iron Gate Repair restores bent, rusted, or broken iron gates to safe working order, whether they’re ornamental driveway gates or simple yard enclosures. You need it when a picket snaps, a rail sags, or the gate scrapes the ground every time it swings. We straighten, weld, and reinforce the iron, then address the rust that caused the failure in the first place. Iron gate repair in Oxnard typically costs $175 to $500 for welding and straightening, and $500 to $1,200 when multiple sections need rebuilding. The quote you get is the price you pay.
Bent Rail and Picket Straightening
Vehicle bumps and wind storms bend top rails and snap pickets at the welds. We remove the damaged section, straighten or replace the steel, and weld it back with matching profile stock. The gate looks right and swings clean when we’re done.
Rust Treatment and Repainting
We don’t just patch rust, we cut it out or grind it back to bare metal, treat the surface, and prime before painting. On gates near Channel Islands Beach, that means repairs that survive the marine air instead of failing again in two years.
Sliding Gate Repair
Sliding Gate Repair fixes cantilever and track-style slide gates that bind, rattle, or stop moving altogether. You need it when the gate jerks along its track, the motor strains, or the gate won’t seat fully against the receiver post. We service the mechanical side, rollers, tracks, and drive, plus the electric operator that powers it. Sliding gate repair in Oxnard runs $200 to $700 on average, with full operator replacement pushing higher. Every price is quoted and approved before work starts.
Roller and Track Alignment
Slide gates depend on perfectly aligned rollers riding a clean track. We replace seized bearings, shim rollers, and clear the track so the gate rolls without the shudder that wears out motors prematurely. Most binding slide gates are a track alignment problem, not a motor problem.
Operator and Limit Adjustment
When a slide gate over-travels and slams the receiver post, or under-travels and leaves a gap a car can squeeze through, the limits are off. We recalibrate travel limits, adjust the safety edges, and test the full open and close cycle until it’s exact.
Wrought Iron Gate Repair
Wrought Iron Gate Repair focuses on ornamental ironwork, the decorative driveway gates and pedestrian gates common on older Oxnard homes near the beach and downtown. You need it when scrollwork breaks loose, the gate rusts at ground level, or the hinges seize so badly the gate won’t move without dragging. We replicate the original design details where sections need replacing, not just weld on whatever’s available. Wrought iron repair in Oxnard runs $200 to $600 for typical scroll and hinge work, and $600 to $1,500 when large sections of decorative iron must be fabricated to match. Estimates are free and the final price is locked before the torch comes out.
Scrollwork and Decorative Element Repair
Ornamental scrolls and finials break at their attachment points. We weld them back with the gate braced in position, preserving the original pattern. When a piece is beyond repair, we fabricate a matching replacement so the gate doesn’t look patched.
Ground-Level Rust Repair
The bottom rail of a wrought iron gate sits in irrigation spray and standing water after winter rains. We cut out the rotted metal, weld in new stock, and coat the repair so moisture can’t get back in. The gate stands square on its hinges again.
Metal Gate Repair
Metal Gate Repair covers aluminum, steel, and chain-link gates, both the frame and the hardware. You need it when a gate post wobbles, the latch won’t catch, or the gate has to be lifted to close. We repair or replace posts, hinges, latches, and frames, and we handle the automation on metal gates too. Metal gate repair in Oxnard runs $150 to $500 for most hardware and post work, and $300 to $800 when sections of the frame need welding or replacement. We tell you the price before we start and we don’t add surprises at the end.
Post Replacement and Reset
A leaning metal gate is almost always a post problem. We dig out the old post, set a new one in concrete at the correct depth, and let it cure before re-hanging the gate. The hinges line up, the latch catches, and the opener stops fighting the sag.
Latch and Hinge Hardware
Loose latches and worn hinges make a metal gate bang in the wind and wear out its own frame. We replace hardware with heavy-duty components sized for the gate’s weight, then adjust so the gate closes fully without slamming.
Wood Gate Repair
Wood Gate Repair fixes sagging, rotting, or sticking wood driveway and yard gates, including the posts and hinges they hang on. You need it when the gate drags on the driveway, the boards pull away from the frame, or the post is soft at ground level. We repair or rebuild wood gates and can reinforce them with steel where the original construction was too light. Wood gate repair in Oxnard runs $175 to $450 for sag and hinge repairs, and $450 to $1,000 when we’re rebuilding the gate or replacing a rotted post. The price is quoted before any work begins.
Sag Repair and Cross-Bracing
Wood gates sag when the frame lacks proper diagonal bracing. We re-square the gate, add or replace the brace, and tighten or replace hinges. The gate closes square against the stop instead of dragging a trench in the dirt.
Rotted Post and Bottom Rail Replacement
Oxnard’s irrigation and occasional heavy rain rot wood gates at the bottom rail and posts first. We replace those sections with pressure-treated stock and seal the end grain. The gate gets another decade instead of another year.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We service LiftMaster gate operators more than any other brand in Oxnard, because they’re the most widely installed residential and commercial operator in North America. If you’re weighing options, read our guide on Choosing the Right Gate Repair Brand: A Buyer’s Guide for Oxnard. We know their control boards, their limit switch layouts, and the failure points on both the LA400 residential series and the commercial slide operators. When a LiftMaster won’t respond, we’re not guessing at the wiring.
FAAC and BFT are the professional-grade operators we see on higher-end Oxnard properties and commercial sites. We work on their hydraulic and electromechanical units, replace their control boards, and re-set their travel limits to factory spec. Linear operators, from basic residential swing units to commercial slide drives, are also well within our wheelhouse. Whether you have a Ghost Controls kit on a backyard fence or a DoorKing access system at a storage facility, we work on your brand. If you have home gate equipment from another manufacturer, call us and we’ll tell you honestly whether we can service it.
Signs You Need a Pro Right Now
- The gate opens partway and reverses. This usually means a safety edge or photo eye is tripping, or a limit switch has failed. A gate that won’t complete its cycle leaves your property open or traps you inside.
- The motor hums but the gate doesn’t move. A stripped drive gear or a seized bearing will burn out the motor if you keep pressing the remote. The longer it runs like this, the more expensive the repair gets.
- The gate scrapes or drags on the ground. On a wood gate, that’s usually a rotted post. On a metal or iron gate, it’s a hinge pulling out. Either way, every cycle is doing damage.
- The remote or keypad works intermittently. Intermittent operation is often a failing control board or a loose wiring connection inside the operator housing. It won’t fix itself and it will fail completely at the worst time.
- You can see cracks at hinges or welds. A visible crack is a structural failure in progress. Gate sections are heavy, and when they come loose they can injure people or damage vehicles.
Our Process, Step by Step
- 1
You call and describe the symptom. Tell us what the gate is doing, what brand it is, and whether it’s swing or slide. We often have a good read on the problem before we arrive, which means we bring the right parts on the first trip. The call to (833) 589-9922 is free.
- 2
We diagnose on site. Lloyd Alvarado or a team member tests the operator, checks the mechanical components, and traces the wiring. We use multimeters on control boards, test loop detectors, and measure gate weight and travel. We find the actual failure, not just the symptom.
- 3
You get a written quote. We tell you exactly what’s wrong, what we’ll do to fix it, and what it costs. The price is agreed before we touch a tool. No hourly mystery billing, no surprises at the end.
- 4
We complete the repair. Most residential gate repairs are finished the same visit. We carry common LiftMaster, FAAC, and Linear parts on the truck, and we source OEM components for other brands fast. Commercial jobs get a clear timeline before we start.
- 5
We test everything and walk you through it. The gate cycles through full open and close, the safety features are verified, and we show you what we did. You get the old parts back if you want them. If the gate fails the same way within our warranty period, we come back and make it right.
How Much Does Gate Repair Cost in Oxnard?
Gate Repair pricing in Oxnard typically runs between $175 and $650, with most jobs landing in the $200 to $400 range. A simple hinge replacement or limit switch recalibration is on the lower end. A failed control board or motor replacement pushes toward $650. Full commercial operator replacement can exceed $1,200. The variables are the gate’s weight, the operator brand, and whether the failure is mechanical or electronic.
What affects the price the most is whether the motor and control board are still good. Mechanical repairs (hinges, rollers, track work, welding) are usually less expensive than electronic repairs. The brand matters too: OEM LiftMaster and FAAC parts cost more than generic equivalents, but they last longer and integrate correctly with the existing system. Coastal corrosion adds labor when rusted fasteners have to be drilled out. A gate that’s been poorly maintained for years costs more to repair than one that’s been serviced regularly.
Our Service Area Near Oxnard
We serve Oxnard and the surrounding areas: Ventura, Camarillo, El Rio, Santa Paula, Channel Islands Beach, Casa Conejo, Thousand Oaks, Moorpark, and Ojai. Most residential calls in Oxnard are answered same-day when you call before noon. If you’re in Ventura or Camarillo, we schedule visits around the same routes, usually within one to two days. For gate repair in Oxnard proper, we’re typically on site within hours of your call. We know the neighborhoods from the beach communities to the inland developments, and we know what the coastal air does to gates in each of them.
Serving Oxnard, CA – Our Local Coverage Area
We’re based in the Oxnard area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Oxnard
Gate repair means diagnosing and fixing a gate that won’t open, won’t close, or won’t operate safely. That includes mechanical work on hinges, tracks, rollers, and frames, plus electrical work on motors, control boards, sensors, and wiring. We handle both the gate structure and the automated operator that moves it.
Most residential gate repairs in Oxnard are completed in one to three hours on site. Mechanical repairs like hinge replacement or track alignment go faster, while control board replacement and welding take longer. Commercial jobs may take half a day or more depending on the operator and access system.
Most gate repairs in Oxnard run between $175 and $650 depending on the failure. Simple hinge and latch work starts around $175, while motor and control board replacements run $400 to $650 or more. Every job is quoted before work begins, and the estimate is free. Call (833) 589-9922 for an exact quote.
Yes. LiftMaster is the brand we service most often in Oxnard, across both residential and commercial installations. We carry common LiftMaster parts on the truck and know their control boards, limit systems, and failure points in depth.
We answer emergency calls for gates that are stuck open, stuck closed, or blocking access. Same-day service is available throughout Oxnard and nearby cities when you call early in the day. For commercial properties with a security gate down, we prioritize those calls.
Yes. Parts we install carry the manufacturer’s warranty, and our labor is warrantied against failure of workmanship. If a repair we made fails within the warranty period, we return and fix it at no charge. The warranty terms are spelled out before you approve the work.
Clear the area around the gate so we have room to work, and keep pets inside during the service call. If the gate is automated, have the remote and keypad codes ready so we can test the full system. Knowing the brand and model helps us bring the right parts on the first trip.
Schedule Your Gate Repair Service in Oxnard Today
If your gate is stuck, sagging, or silent when you press the remote, call (833) 589-9922 now. We’ll schedule a visit, diagnose the problem on site, and give you a free, no-obligation quote before any work starts. Lloyd Alvarado and the Gate Repair Oxnard team are ready to get your gate moving today.
Written by Lloyd Alvarado, Owner at Gate Repair Oxnard, serving Oxnard and surrounding Ventura County communities.